Home / Skin temperature probes / Disposable temperature probes — for incubato
Disposable temperature probes — for incubators, warmers and single-patient use
FDA clearancesK182667 · K193338
UseSingle-patient
SettingsIncubator · warmer
ReferencesDräger · ATOM…
In the incubator, the temperature probe is part of the servo loop that heats the baby — a probe that reads low overheats the patient; a probe that falls off does worse. Disposable probes remove reprocessing from that loop: a fresh, known-good sensor per patient. This range covers disposable temperature probes for infant incubators and radiant warmers, cross-referenced to the warmer references departments order by (Dräger MX11001-type and ATOM 60884-type references among them), plus the adapter cables that join disposable probes to monitor channels.
Temperature probes are an FDA-cleared family for this factory (K182667, with reusable and disposable probes under K193338) — for US neonatal and paediatric buyers, the line can be qualified against named clearances.
Warmer and incubator probes
Servo-control probes are specified by the warmer/incubator system, not by the monitor: the connector and the thermistor curve belong to the warmer's control unit. Order against the warmer reference — the cross-reference carries the common ones — and keep probe covers/reflective patches in the same stock, since adhesion on neonatal skin is managed with covers, not pressure.
- Disposable probes for infant incubators
- Radiant warmer servo probes (Dräger/ATOM-type references)
- Adapter cables to monitor temperature channels
Single-patient probes beyond the NICU
Disposable probes also serve isolation and infection-control contexts in general wards, and theatres where reprocessing turnaround is the bottleneck. Where a reusable probe would be used with a single-patient cover, covers are stocked within the wider temperature range as the alternative pattern.
Representative products from the current catalogue
| Product (official store listing) | Key specifications |
|---|---|
| 60884 ATOM Disposable temperature probe Compatible for Infant Incubators/Warmer | Atom: 60884, NF-023；NOVAMED: 10-2000D-020 (Box of 20), 10-2000D-060 (Case of 60)；GE Healthcare > Critikon > Dinamap: Carescape One；Category: TEMP.；CMonitor End Connector: Round, 6-Pin Connector, Keyed；Channel: Single；Latex-free: Yes；Packagi |
| Draeger MX11001 Disposable temperature probe Compatible for Infant Incubators/Warmer | Draeger Air-Shields: MX11001；Category: TEMP.；Monitor End Connector: Rectangular, 2-Pin Connector, 90° Angle；Channel: Single；Latex-free: Yes；Packaging Unit: 24；Resistor Type: NTC Series；Weight: 1pcs=0.04lb 1Box (24pcs) =1.2lb；Total Cable Len |
| Draeger Temperature Adapter Cable Compatible for Disposable YSI 400 Seriers Probe | Draeger: 11-CA-407-12 (12 ft (3.6 m)), 11-CA-407-04 (4 ft (1.2 m))；Category: TEMP.；Monitor End Connector: Round, 7Pin Connector；Channel: Single；Latex-free: Yes；Packaging Unit: 1；Resistor Type: NTC Series；Weight: 0.15lb；Total Cable Length: 2 |
| Draeger-Air-Shields Compatible Infant Incubator（Warmer） disposable Temperature Probe MU06933 | Datex Ohmeda: 10-1910-020, 10-1910-060；Draeger Air-Shields: MU06933, MU06935, MU06951, 68-209-20, 68-209-30, 68-209-70；Category: TEMP.；Monitor End Connector: Round, 3-Pin Connector, Keyed；Channel: Single；Latex-free: Yes；Packaging Unit: 24；R |
| Philips Compatible Disposable Temperature Probe - 989803100951 | Philips: 21091A, 989803100951, DHP-D-N0 (Old CS SKU)；CAS Med: 750；Carewell: CPM-9000T；Criticare: 1100, 2200, 506, 507, 507E, 507ELC, 507S, 508, 8100；Datex Ohmeda: CS/3, Cardiocap I, Cardiocap II, Cardiocap/5, Light Monitor, M-ESTP, S/3, S/5 |
| Philips Compatible Disposable Temperature Probe - M1837A | Philips: 21090A, 989803100941, M1837A, 989803105321 (Pediatric), DHP-DAG-N0 (Old CS SKU) Compatibility:；CAS Med: 750；Carewell: CPM-9000T；Criticare: 1100, 2200, 506, 507, 507E, 507ELC, 507S, 508, 8100；Datex Ohmeda: CS/3, Cardiocap I, Cardioc |
Questions & answers
Are disposable incubator probes FDA-cleared?
Yes — temperature probes are cleared under 510(k) K182667, with reusable and disposable probes under K193338.
How do I order the right warmer probe?
By the warmer/incubator system's reference (for example the Dräger or ATOM probe reference you currently use). The warmer, not the monitor, specifies the probe.
Can disposable probes connect to a standard monitor?
With the matched adapter cable where the series allows; tell us the warmer probe and the monitor channel and we confirm the chain.
See also: Temperature adapter cables · All temperature probes · YSI-compatible range